Can I use a 52v battery on a 48V motor and controller?
52v batteries have a maximum voltage with a full charge of 58.8v, so this is a safe voltage for the components in a 48v controller. Motors are even more tolerant.
How do you match an ebike battery and controller?
The battery voltage needs to match the motor rating. The controller voltage rating needs to be the same or higher. The battery AH rating should be chosen based on the motor power rating ÷ motor voltage rating x 1hr.
What is the difference between a 48V and 52V ebike battery?
A 52V e-bike battery provides a faster speed to the motor than a 48V. One of the most important differences is related to the range, a 52V e-bike battery offers a range wider than a 48V.
Can I use a 52V battery on a 48V Bbshd?
Change the battery setting to UBE and it will autodetect the correct voltage. I use my BBSHD with both 48 and 52V batteries but I use a CAV2. 4 to keep an eye on the voltage.
Can a 48V controller handle 72V?
You'd have to know what caps and fets it has. All the 48V controllers I've seen have 63V caps and fets not much higher which would make them not capable of using a 72V battery pack. OTOH, you can get a controller capable of up to 100V for about $35 shipped.
Can 48V controller handle 52V battery?
52v batteries have a maximum voltage with a full charge of 58.8v, so this is a safe voltage for the components in a 48v controller. Motors are even more tolerant. They just spin faster, given higher voltages.
How do I match my battery and controller?
The controller's low Voltage cut off level should be the same as or lower than the lithium battery's discharge cut off Voltage level. The lithium battery's maximum continuous discharge current rating needs to be higher than the controller's maximum current rating.
Can I use 52V with a 48V motor?
In conclusion, using a 52V battery on a 48V motor can provide enhanced speed, power, and range, making it an attractive option for many riders. While compatibility concerns may arise, reputable companies like Electrify Bike have tested and verified the compatibility of 52V batteries on 48V motors.
Is 52V better than 48V?
Which Is Better: 48V or 52V? The biggest difference in battery voltages appears when either battery is about half discharged. At that point, for a 48V battery, a significant power drop occurs. A 52V battery will not experience the same drop in power at the halfway point, making it a better choice.
How far can a 52V 20Ah battery go?
52V 20Ah Ebike Battery is over 80 miles per charge on pedal-assist mode and around 50 miles on pure electric power mode.
Can you run a 52 volt battery on a 48 volt ebike?
They are both 48V and the same Ah,s! The short answer is yes, this is fine as long as they have the same voltage.
Can I charge a 52V battery with a 48V charger?
Yes, they absolutely do. IF you purchase a 48V battery, you MUST HAVE a 48V charger, which will charge to NO HIGHER THAN 50.4V. You have at least two and possibly three meters showing a charge of 53-54V. Including one at or more than 54.6, the max charge for a 52V battery.
Can I use a bigger battery on my ebike?
Yes, a bigger battery can be installed on an electric bike. For example, if an Electric Bike has 25 AH of battery pack and you have a 36AH battery pack then it can be higher than 30% of the original battery capacity without any problem.
Can I use 60V on a 48V controller?
That would definitely not be a good idea unless you use a 48V charger, your existing 60V charger would overcharge the 48V pack.
Can I use 60V battery on 48V controller?
At worst, you will need a new controller, but if max charge is 60V, then it will work fine without a problem.
What is the cutoff voltage for a 48V controller?
A 48v battery is fully charged at 54.6v. The low voltage cutoff is around 39v. It is best not to discharge more than 80% of the capacity for good cycle life. 80% DOD is around 43v depending on cell chemistry.
Can I use a 36V battery with a 48V controller?
It probably won't work because the voltage is too low. An electronic motor controller will shut off below a minimum voltage. A 48 volt motor will barely run at 12 volts and will have little torque. Lights and instruments won't work at too low a voltage either.
What is the maximum voltage for a 48V system?
At the other extreme, the maximum voltage for a -48 V power system is normally specified to be -60 V continuous, with transients up to -100 V (refer to ANSI T1. 315). However, some central offices use a nominal -60 V power system rather than the normal -48 V.
How many cells in a 52V battery?
Each 18650 cell typically has a nominal voltage of 3.7 volts and a typical capacity of around 2500-3000mAh. To achieve a 52 volt output, you would need to connect 14 cells in series (14 cells * 3.7 volts/cell = 51.8 volts).
How many solar panels do I need to charge a 48V 200Ah battery?
48V and 200Ah is 9,600 Watt Hours. Sourcing that amount of energy in 5 hours requires 1,920 watts. If each panel really generates 310 watts over the full 5 hours that means you'll need 6.19 panels.
Why do controllers need two batteries?
Because a single cell would not provide sufficient voltage for the components inside the device to operate correctly. Alkaline or zinc-carbon cells provide 1.5 volts. This is a little low for most electronics, so two cells are used to give an overall voltage of 3 volts.
Can you connect 2 MPPT to one battery?
In this setup, each charge controller assesses the battery voltage and chooses the amount of current that is sent to its own solar panel. It's quite common to use two or more controllers with a single battery bank. It's particularly useful in big arrays because of how MPPT controllers operate.
Can I use a lower voltage battery on a higher voltage motor?
Not necessarily. It depends on how the motor is applied to the job at hand. There are times when it would be appropriate to run a motor at less than rated voltage, for very-long-term reliability, improved safety margins, or for improving Power-Factor.
What is the low voltage cut off for a 52v battery?
Using a simple ratio, the cutoff for a 52v battery would be 44.46v.
How fast can a 48V 500W motor go?
A 500W motor provides speeds of around 18-22mph, suitable for short rides. On the other hand, a 1200W motor offers a significant boost, pushing max speed to 25-30mph, making it ideal for hilly terrains. If you crave exhilarating speeds, the 1500W motor propels you at an average of 35mph.
